PLUMBING BASICS: YOUR KEY TO INSTALLING A BATHTUB

Plumbing Basics: Your Key to Installing a Bathtub

Plumbing Basics: Your Key to Installing a Bathtub

Blog Article

Contact Us Today

This post which follows pertaining to Installing A Bathtub is amazingly interesting. Don't skip it.


How to Install a Bathtub Yourself
Installing a bath tub isn't precisely rocket science, however it does call for solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is also a moderately difficult project. If the old tub is readily available, the project can relocate quickly; if you need to open a wall surface to remove the old bathtub and also position the brand-new tub, the job is a lot harder. In either case, the job is within a home handyman's abilities, although you will certainly require an assistant to move out the old tub and also set in the new one. See to it you have qualified on your own for the job and are comfortable trying it. Rather than hiring a specialist to take over a halfway-completed job, it is better to consider employing one before you begin. Chances are you might require a professional plumber to make tube connections.
This write-up will certainly help you mount a brand-new tub in your bathroom if you have already gotten a brand-new bathtub and also do not require to transform the plan of your previous water pipes.
Your devices as well as material checklist should comprise the following:
  • New Bath tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipeline Caps


  • Removing Old Taps


    If you require to replace old faucets with brand-new ones as a part of your setup, after that the first thing you must do is disconnect the supply of water. After doing so, turn on the faucets to drain any type of water remaining in the system. The process of removing the existing taps can be quite troublesome because of the restricted gain access to that is often the instance.
    Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the taps. Have a fabric all set for the staying water that will certainly come from the pipelines. As soon as the supply pipes have actually been gotten rid of, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from transforming throughout this process. Once the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old securing compound.
    Prior to going on to fit the new taps, contrast the pipeline links on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new faucets to fit.

    Suitable New Taps


    If the tails of the brand-new faucets are plastic, then you will need a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end supplies a connection to the existent supply pipelines.
    If you need to fit a monobloc, then you will certainly require reducing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
    Next off, position the tap in the placing opening in the bath/basin guaranteeing that the washers remain in place in between the tap and also the sink. Protect the faucet in place with the manufacturer provided backnut. As soon as the faucet is securely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal faucet adapters. The previous type should be linked to the tap finishes initially, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have actually been attached.

    Mounting the Tub


    Making use of both wooden boards under its feet, put the tub in the required setting. The wooden boards are practical in uniformly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 tiny points.
    The next objective is to ensure that the tub is leveled all round. This can be achieved by examining the level as well as readjusting the feet on the bath tub up until the level reads level.
    To mount taps, fit the bottom of the outermost adaptable tap adapter to the suitable supply pipeline by making a compression join; after that do the exact same for the various other tap.
    Switch on the water system and also examine all joints as well as new pipework for leaks and tighten them if required. Fill the tub as well as likewise inspect the overflow outlet as well as the regular outlet for leaks.
    Ultimately, take care of the bathroom paneling as described in the producer's user's manual. Tiling as well as securing around the bath tub must wait up until the bath tub has been utilized a minimum of when as this will certainly settle it into its final position.

    Getting ready for the Installment


    Firstly, the sustaining structure supplied with the bath ought to be fitted (if called for) according to the supplier's directions. Next, fit the taps or mixer to the tub. When suitable the tap block, it is essential to make certain that if the tap includes a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets system to prevent stress on the bathtub.
    Fit the versatile tap adapters to the bottom of both faucets making use of 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet through the hole in the bathroom. Use the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next off, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you make use of every one of the supplied washers.
    Link the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath ought to currently prepare to be fitted in its last position.

    Tiling Around the Tub


    In the location where the bath fulfills the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the fitting can relocate enough to break an inflexible seal, triggering the water to penetrate the wall surface in between the bathroom as well as the tiling, resulting in difficulties with wetness and feasible leaks to the ceiling below.
    You can choose from a range of coloured sealants to blend in your fixtures and fittings. They are offered in tubes and cartridges, and can sealing spaces up to a width of 3mm (1/8 inch). If you have a larger space to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to constantly load the tub with water prior to securing, to permit the activity experienced when the tub is in usage. The sealant can fracture relatively very early if you do not take into account this activity before sealing.
    Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally conveniently available on the market. It is advisable to fit the tiles using water-resistant or water resistant glue as well as grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    A Step-by-Step Guide to Installing a Bathtub

    Do you really like reading up on Tools You Need to Install a New Bathtub ? Give feedback down the page. We would be pleased to know your views about this content. We are looking forward that you visit us again before long. Are you aware of anybody else who is inquisitive about the subject? Do not hesitate to promote it. We take joy in reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.


    Visit Website

    Report this page